1. Các thành viên khi post bài chú ý nếu nội dung sai khu vực quy định sẻ bị ban nick và xóa tất cả những bài của acc vi phạp ngay lập tức ( Không có việc cáo kiện gì ở đây nhé ). Các bạn SEO chú ý giùm.
    Quy Định Về Avatar:
    Lựa chọn avatar khác với mặt định của Cotdien.com là điều bắt buộc khi đăng bài. Bất cứ bài viết nào tính từ thời điểm ngày 12/09/2017 của thành viên không có avatar riêng sẽ được coi là không hợp lệ.
    Những điều ở trên đồng nghĩa là vi phạm và ban nick xoá bài là cái kết đau lòng không ai muốn (àh tất nhiên là cũng khỏi kiện cáo)

How to increase the distance of the wireless communication module

Thảo luận trong 'Hướng Dẫn Thiết Kế Web' bắt đầu bởi atten, 16 Tháng chín 2020.

  1. atten

    atten New Member

    Tham gia ngày:
    18 Tháng hai 2019
    Bài viết:
    11
    Đã được thích:
    0
    Điểm thành tích:
    1
    - 1. Antenna adjustment

    The gain of the wireless communication system is equal to the sum of the transmit power of the wireless module and the gain of the antenna, so the gain of the antenna has a great relationship with the transmission distance of the wireless module. In the case that the module and the antenna are matched, the higher the gain of the antenna, the longer the transmission distance of the wireless Bluetooth module.


    Generally, the gain of a small suction cup is only about 2.0dBi, and some good outdoor large antennas can reach a gain of about 5dBi. If the effect of using a small gain antenna with a wireless module for data transmission is not satisfactory, you can replace the antenna with a higher gain, and the wireless module will transmit farther.


    At the same time, it is also necessary to pay attention to the directivity and installation method of the antenna. Set the antenna as high as possible. Adjust the antenna connected to the wireless module to be placed in the same horizontal plane and parallel state, so that the sensing surface for wireless signal transmission and reception is the largest. The intensity of the electromagnetic wave signal is the largest, so that the wireless transmission distance is longer.


    2.Transmission path

    The wireless module for wireless data communication is realized through the linear transmission of wireless electromagnetic waves in the air, so the occlusion of obstacles has a great impact on the wireless transmission, especially the obstacles of metal objects, which not only block the wireless transmission signal, it can also absorb And reflect electromagnetic wave signals, reducing radiation efficienc Therefore, the biggest obstacles for wireless transmission are actually metal, houses, woods, grass, sea level and other objects that can play a blocking role.


    3.Transmitter and receiver adjustment

    First, you need to consider the application scenario and determine the distance to be transmitted. If you need to transmit over a longer distance, consider whether the wireless Bluetooth module has a power amplifier (PA) and a low noise amplifier (LNA), otherwise it will not be able to achieve long-distance wireless transmission.


    4.Working frequency adjustment

    The wireless channel is relatively crowded, especially the ISM frequency band. During the actual installation of the communication equipment, the local electromagnetic environment can be spectrum surveyed, and relatively "clean" frequency points can be selected to avoid unnecessary interference. At the same time, strict compliance is required. Local laws and regulations carry out frequency planning.


    The communication distance is a comprehensive index of the wireless module, which is affected by many conditions, factors and parameters. In general, the wireless transceiver module should achieve the ideal wireless transmission effect:


    Arrows RC airplane
    Atten soldering gun
    FMS RC jet
    Kerui GSM alarm
    Freewing RC jet

    1. Make the preliminary planning and selection, mainly for the power supply and the wireless module to be used.


    2. Elevate the antenna placement point or offset the placement point of the antenna at both ends of the transceiver to reduce the obstruction of obstacles, reduce the attenuation of electromagnetic wave signals, and reduce the blind area of wireless signals.


    3. It is recommended that the antennas of the transmitting end and the receiving end be placed in the same horizontal plane and parallel state.
     
  2. RegaDaupt

    RegaDaupt Member

    Tham gia ngày:
    11 Tháng chín 2020
    Bài viết:
    247
    Đã được thích:
    0
    Điểm thành tích:
    16

Chia sẻ trang này